Have you ever had your KitchenAid dishwasher beeping and flashing clean even when the wash cycle is not finished? This frustrating issue can really be a headache and disrupt your daily kitchen routine.
A beeping dishwasher is a type of error code that indicates a problem. There can be several causes for a dishwasher beeping clean like water supply issues or soapy interior. Understanding the reasons why your KitchenAid dishwasher won’t stop beeping can help you easily diagnose and fix the problem.
In this article, we will walk through the most common reasons why your KitchenAid dishwasher keeps beeping and flashing and provide you with the right troubleshooting steps to fix the error code without calling an expensive technician.
Why is the clean light blinking on my KitchenAid dishwasher?
The clean light blinking on your KitchenAid dishwasher indicates a problem with the overfill protection float. This float switch prevents the dishwasher from overfilling with water. If it gets stuck, damaged, or blocked, it will be unable to move freely and the dishwasher will not fill properly. As a result, you will see the blinking clean light on your Kitchen Dishwasher.
Besides this, there are a few other potential causes that can cause a blinking clean light:
- Using the wrong type of detergent:- Dishwasher detergents are made specifically for dishwashers. Using hand or laundry soaps can cause excess suds and cleaning issues.
- A water supply problem:- If the water supply valve is turned off or faulty, the dishwasher won’t get enough water and start to beep the clean light.
- Not replacing the rinse aid dispenser cap:- Leaving the cap off after filling the rinse aid can lead to excess suds and beeping issues.
- Too much dishwasher detergent:- Adding too much amount of soap can lead to extra suds that can trigger the to beep clean light.
- A control board glitch: Being an appliance, your dishwasher can experience software glitches on the circuit board.
Fortunately, most blinking clean light causes can be addressed with simple fixes. Inspecting the overfill float, using compatible detergents, and resetting the dishwasher are common solutions for a blinking clean light problem.
How can I fix the beeping and flashing clean light on the KitchenAid dishwasher?
Now, most of the blinking clean light causes can be resolved by simple DIY steps. Here are those which you can follow to troubleshoot the beeping KitchenAid dishwasher:
Use recommended detergent
If your KitchenAid dishwasher is beeping and flashing a clean light, it can be due to using the wrong type of detergent. Dishwasher soaps are designed for the specific cleaning needs of a dishwasher. When you use laundry soaps it produces excess suds and cleaning issues that trigger the blinking clean light.
How to fix it?
To fix this problem, only use detergents made specifically for dishwashers and avoid any hand or laundry soaps. Also, ensure that the packet says “dishwasher safe”.
Fix the software glitch
A software glitch can be the reason for a flashing clean light on your KitchenAid dishwasher. Like any other electrical appliance, dishwashers can also face the software glitch occasionally. As a result, the dishwasher starts beeping and flashing the clean light.
How can I fix this?
First, unplug the dishwasher from the power source or turn off the circuit breaker for 5-10 minutes. This resets the control board. Next, plug the dishwasher back in and turn on the circuit breaker.
Check for water supply issues
An issue with the water supply can create many dishwasher problems along with this one. If a dishwasher will not have adequate water flow, it will be unable to function properly. This causes it to malfunction and you will see the beeping clean light on the front panel.
How to fix the water supply problem?
First, check under the sink to ensure the water supply valve is turned on and open. You can turn the valve handle counter-clockwise to open it.
Next, inspect the water supply line for any kinks that can block the water flow. If you find any bent or folded pipe straighten it and run the dishwasher to check if it’s getting sufficient water.
If the clean light is still blinking, it means the water inlet valve is malfunctioning and you should replace it.
Inspect for the suds issue
Suds are the foam that is created when the dishwasher soap is mixed with the water. In case you fill too much detergent in your dishwasher, excessive suds will be produced that will prevent the water from filling and circulation in the dishwasher during the wash cycle. This disrupts the operation of the appliance leading to a flashing clean light.
How to fix the suds problem?
- First, remove all the dishes from the dishwasher tub.
- Then, pour 1/4 cup vegetable oil or 2 tablespoons salt into the bottom to help suppress and break down the suds.
- Next, run an empty cycle or “quick rinse” to flush out the remaining suds.
- Repeat the same process the until suds are gone.
- Lastly, add a cube of ice to melt the remaining foam.
To prevent this, reduce the amount of soap you use to clean the dishes.
Check for the stuck overfill protection float:
The float switch is responsible for preventing overfilling in the dishwasher by shutting off the water flow. But if it gets stuck or blocked by some debris or food particles, it will be unable to move and do its job. As a result, you will see a blinking clean light on your KitchenAid dishwasher.
How can I fix this?
- Identify the float in the front right corner of the dishwasher tub.
- Then, check that the float moves up and down easily. Move it with your hand to test.
- If it’s stuck, press it down to release it and make sure it moves freely.
- If found, remove the debris or obstacles blocking the float switch.
- At last start a cycle to verify water filling has stopped and the dishwasher has a proper level of water.
Replace the rinse aid dispenser cap
If you forget to replace the rinse aid dispenser cap after refilling, it can cause a flashing clean light on your KitchenAid dishwasher. When you leave the cap off after refilling the rinse aid, it can lead to excess suds inside the dishwasher leading to a beeping and flashing clean light.
How to fix this?
- Ensure that the rinse aid dispenser cap is present and properly attached after adding the rinse aid.
- Replace any damaged or missing rinse aid caps immediately and make sure the dispenser is properly sealed.
- Lastly, run an empty “rinse only” or quick cycle to clear out all suds that entered when the cap was opened.
How to reset the flashing clean light on the KitchenAid dishwasher?
Using reset sequence
- First, turn on the dishwasher and ensure that it is in the normal mode.
- Then, press the “Heat temp wash” and “Heated dry” buttons four times.
- Finally, press “High Temp Wash” one more time to reset the control board.
- Now, wait for the clean light to stop flashing, then press “Cancel/Drain” button.
- Lastly, run the hot water to clear any remaining suds and start a fresh wash cycle.
Perform a hard reset
If the above method doesn’t resolve the beeping and flashing clean light, try a hard reset using these steps.
- Flip the circuit breaker switch of the dishwasher to cut off the power.
- Then, disconnect the cord from the electrical outlet and wait for 1-2 minutes before plugging it back.
- After 1-2 minutes, plug the dishwasher’s cord back in and turn on the circuit breaker to restore the power.
What are some other beeping issues on the KitchenAid dishwasher?
KitchenAid dishwasher clean light blinking 4 times then 8 times.
If your KitchenAid dishwasher’s clean light is blinking 4 times then 8 times, it indicates an issue with the water levels. This error code signals the dishwasher is not filling correctly.
Follow these steps to fix the issue:
- Make sure recommended dishwasher soaps are being used. Hand or laundry soaps can cause excess suds leading to water level problems.
- Next, try resetting by turning off the breaker switch for 5 minutes.
- Ensure that the water supply valve is open and water is getting into the dishwasher.
- Inspect the drain pump and inlet water valve for any issues.
- Ensure the float switch moves freely and isn’t obstructed.
- Remove the extra water from the drip tray behind the kick panel that can lift the protection float switch and disrupt the water level.
KitchenAid dishwasher clean light blinking 6 times
When a KitchenAid dishwasher blinks clean light for 6 times it means there is an issue with the heating element or the control board is not detecting electrical continuity in the heating circuit.
Here is how to fix this:
- First, try to solve the error by performing a reset. To do so, unplug the dishwasher from the power source for 5 minutes.
- Next, use a multimeter to check the heating element for continuity. If no continuity is found, replace it with a new one.
- Ensure that the wire connections to the heating element are secure and don’t have any cuts or corrosion.
- Next, reset the control board by pressing the buttons of the control panel in this sequence. “High Temp Wash” and “Heated Dry” buttons 4 times, then “High Temp Wash” for once.
- Lastly, run a hot water rinse cycle to check the proper functioning of the heating element before dishwashing again.
KitchenAid dishwasher beeps 3 times
The KitchenAid dishwasher beeping 3 times signals that your appliance has a low water supply or water pressure. The dishwasher is not filling properly with enough water to complete the wash cycle.
Some common causes and fixes for 3 beeps:
- Check if the water supply valve is fully opened and water lines are not kinked or blocked.
- Inspect the water inlet valve for damage. Use a multimeter to test its continuity and replace the inlet valve if found faulty.
- Ensure the float switch moves freely and is not stuck in the up position.
- Look for leaks or clogs that could be preventing proper water filling.
- Run a short cycle to verify water is now filling into the tub.
KitchenAid dishwasher beeps 15 times
Have you ever experienced the KitchenAid dishwasher beeping 15 times issue? This actually indicates an error code detected by the control board.
To fix this:
- Press the “High Temp Wash”, “Heated Dry”, and “High Temp Wash” buttons in sequence – 1, 2, 3 three times.
- Then, press “High Temp Wash” one more time to reset the control board.
- Wait for the clean light to stop flashing then press the “Cancel/Drain” button on the control panel.
- At last, run a hot water cycle to test the functioning of the dishwasher.
FAQs
Why does my KitchenAid dishwasher stop mid-cycle and says clean?
The dishwasher stops mid-cycle because the thermal fuse is shorting out. This fuse acts as a safety switch, stopping operation when the dishwasher gets too hot.
Why does my dishwasher say clean?
The dishwasher going right to clean means the control board detects the drain or circulation pump is drawing too much power initially.
Is KitchenAid a good brand of dishwasher?
KitchenAid dishwashers are excellent home appliance brands that offer high-quality products for a budget-friendly price.
Final Thought
When your KitchenAid dishwasher won’t stop beeping and flashing the Clean light, it can become a headache for the homeowner. But with some simple troubleshooting, you can easily resolve the problem by yourself without calling a professional technician.
In the above guide, we have seen many causes of this problem including a stuck float, low water supply, excess suds, usage of wrong detergent, issues with float, water inlet valve and rinse aid cap along with their troubleshooting guide. But, if you are unconfident or confused about repairing your dishwasher, you can always get help from a pro.
This was all about the guide on KitchenAid dishwasher beeping clean light. I hope you found it useful. If you have any doubts, ask me in the comments below. I will be always there to assist you.
